Kippzonen Brewer MkIII Manual do Utilizador

Service manualSpectrophotometerBrewer MkIII

MKIII SERVICE MANUAL 5 3 MAJOR EQUIPMENT FAILURES A major equipment failure is defined as a condition where there is no communicatio

95 Figure 10.6-2.1

96

97 Figure 10.6-2.2

MKIII SERVICE MANUAL 98 BA-F01/D FORE OPTICS ASSY Item No. Part No. Description Qty 1 BA-F114/B Zenith Drive Assy 1.00 2 BA-F04 F

99 Figure 10.6-2.3

100 Figure 10.6-2.4

101 Figure 10.6-3.1

102

103 Figure 10.6-3.2

MKIII SERVICE MANUAL 104 BA-S120/B DOUBLE SPECTROMETER ASSEMBLY Item No. Part No. Description Qty 1 BA-S110 SPECTR MECH ASSY,

MKIII SERVICE MANUAL 6 If the power supply appears to be normal, then the LED may be defective, or there may be a faulty connection.

105 Figure 10.6-3.3

106 Figure 10.6-3.4

107 Figure 10.6-3.5

108

109 Figure 10.6-3.6

110 Figure 10.6-4.1

111 Figure 10.6-4.2

MKIII SERVICE MANUAL 112 Part List Part No. Description Qty BA-P01/B BA-P02/C-F Photomul

113 Figure 10.6-4.3

114 Figure 10.6-4.4

MKIII SERVICE MANUAL 7 4. Test RS422 adapter The RS422 adapter at the computer can be tested by removing the communications cable from th

MKIII SERVICE MANUAL 115 BREWER REFERENCE DOCUMENTATION Section 10.7 Brewer Options 10.7.1 Option B Option B -- Azimuth Pointing Sy

MKIII SERVICE MANUAL 116 Figure 10.7-1.1

117 Figure 10.7-1.2

118 Figure 10.7-1.3

119 Figure 10.7-1.4

MKIII SERVICE MANUAL 120 Figure 10.7-1.5

MKIII SERVICE MANUAL 121

122 Figure 10.7-3.1

123 Figure 10.7-3.2

124 Figure 10.7.4

MKIII SERVICE MANUAL 8 6. Line Driver If the reset of the motors is heard and seen, but there is no message sent to the PC, then there may

125 Figure 10.8

Our customer support remains at your disposal for any maintenance or repair, calibration, supplies and spares.Für Servicearbeiten und Kalibrierung, Ve

MKIII SERVICE MANUAL 9 8. Check Voltages If the LED is not flashing, then the correct voltages should be confirmed for the power supply o

MKIII SERVICE MANUAL 10 D. Type readlog  to display past error history, each line displayed will be a possible clue to the problem that ca

MKIII SERVICE MANUAL 11 4 OPERATING TEST FAILURES In the Brewer Spectrophotometer, most of the operating tests are done using either

MKIII SERVICE MANUAL 12 2. Check Temperature Observe the temperature of instrument (TE). If the Brewer temperature is less than 0 degrees

MKIII SERVICE MANUAL 13 to the actual high voltage divided by 409. There may be a variation of a volt or two of the high voltage, but the

MKIII SERVICE MANUAL 14 3. Observe Slitmask Performance. If the mercury lamp test is normal, the spectrometer cover should be removed and a

REVISION HISTORY REV DESCRIPTION DCN # DATE APPD - Initial Release ----- 98-11-06 TKLL A New Brewer Elect

MKIII SERVICE MANUAL 15 4.6 LIGHT DETECTION SYSTEM FAILURE A Light Detection System failure may show up in any or all of the diagnos

MKIII SERVICE MANUAL 16 5. Test Slitmask Slitmask operation can be confirmed by returning to Telytype operation (TT), sending the R,0,7,20

MKIII SERVICE MANUAL 17 If these signals are normal, consult KIPP & ZONEN before proceeding further. If any of the signals are missing

MKIII SERVICE MANUAL 18 4.11 RATEMETER The ratemeter circuit provides a voltage output of the photon count rate. It consists of a two-

MKIII SERVICE MANUAL 19 4.16 BREATHER DESICCANT CARTRIDGE The breather desiccant cartridge allows the Brewer to compensate for normal

MKIII SERVICE MANUAL 20

MKIII SERVICE MANUAL 21 5 TEST RESULTS OUT OF SPECIFICATION Whenever any diagnostic tests are out of specification, (SL, HG,DT,RS,)

MKIII SERVICE MANUAL 22

MKIII SERVICE MANUAL 23 6 OPTICS CARE AND CLEANING 6.1 OPTICS CARE - Never touch the polished surface of optics. - Hold an optic

MKIII SERVICE MANUAL 24

ii

MKIII SERVICE MANUAL 25 7 AZIMUTH TRACKER Problems in the Azimuth Tracker affect the Brewer’s ability to track the sun, and thus an

MKIII SERVICE MANUAL 26 7.3 TRACKER ELECTRICAL PROBLEMS Electrical problems include AC power, power supply, motor driver board, stepper

MKIII SERVICE MANUAL 27 5 If no pulses are seen at the Tracker, then look on pin 4, J17T on the Main Electronics board. This pin is the

MKIII SERVICE MANUAL 28 Figure 7.1 Tracker Drive Mechanism

MKIII SERVICE MANUAL 29 8 MAIN ELECTRONICS FIRMWARE / CONFIGURATION LOADING PROCEDURES This procedure is used to upload new firmwa

MKIII SERVICE MANUAL 30 Exit out of the Brewcmd program by typing quit  and the computer will have returned to the dos prompt. Run the BRE

MKIII SERVICE MANUAL 31 These are some of the messages seen while going into the Cosmac mode. Motors should reset and it is ready to run t

MKIII SERVICE MANUAL 32 Type save  a number should appear. This tell you how many configuration writes you had left when the save command

MKIII SERVICE MANUAL 33 9 WARRANTY MANUFACTURER'S GUARANTEE / WARRANTY CERTIFICATE NEW PRODUCT WARRANTY AND LIMITATION OF LIAB

MKIII SERVICE MANUAL 34

iii

MKIII SERVICE MANUAL 35 10 BREWER REFERENCE DOCUMENTATION Section 10.1 Overall Assembly and External Cables Figure - Configu

MKIII SERVICE MANUAL 36 Figure 10.1-1.1

37 Figure 10.1-2.1

38 Figure 10.1-3.1

39 Figure 10.1-3.2

MKIII SERVICE MANUAL 40 BA-C231 BREWER MKIII DBL SPECTR Item no. Part No. Description Qty. 1 AM-BA-C05 BREWER FINAL TEST RECOR

41 Figure 10.1.4-1

42

43 Figure 10.1-4.2

44

MKIII SERVICE MANUAL 45 BA-C91 Item No. Part Number Description 120V Qty 230V Qty 1 BM-C100 Nameplate, Altered, Azimuth Tracker 1.0

MKIII SERVICE MANUAL 46 Item No. Part Number Description 120V Qty 230V Qty 58 85-10-145 Adhesive, Sealant (Loctite 242) 2.00 2.00 59 81

47 Figure 10.1-4.3

48 Figure 10.1-5.1

MKIII SERVICE MANUAL 49 BA-C113 Installation Kit Item No. Part No. Description Qty 1 BA-C91 Azimuth Tracker Assy 1.00 3 83-79-116 Screw

50 Figure 10.1-6

51 Figure 10.1-7

MKIII SERVICE MANUAL 52 BA-C222 Brewer Electronics Spares Kit Item No. Part No. Description Qty 2 BA-C99 Azimuth Tracker Board As

53 Figure 10.1-8

MKIII SERVICE MANUAL 54 BREWER REFERENCE DOCUMENTATION Section 10.2 Power Supply and Harness Figure - Main Power Connect Cable

MKIII SERVICE MANUAL 1 TABLE OF CONTENTS PREFACE ...

55 Figure 10.2-1

56 Figure 10.2-2

57 Figure 10.2-2.1

MKIII SERVICE MANUAL 58 BA-E103/B Power Supply Assembly Item No. Part No. Description Qty 1 BM-E102 Mounting Bracket, Main Po

MKIII SERVICE MANUAL 59 Figure 10.2-2.2

MKIII SERVICE MANUAL 60 Figure 10.2-2.3

MKIII SERVICE MANUAL 61 BREWER REFERENCE DOCUMENTATION Section 10.3 Internal Cabling Figure - Communication Cable Assembl

62 Figure 10.3-1

63 Figure 10.3-2

64 Figure 10.3-3

MKIII SERVICE MANUAL 2 Recommendations by Environment Canada Mark III Brewer Ozone Spectrophotometers are recommended by Environment C

65 Figure 10.3-4

66 Figure 10.3-5

67 Figure 10.3-6

68 Figure 10.3-7

69 Figure 10.3-8

MKIII SERVICE MANUAL 70 BREWER REFERENCE DOCUMENTATION Section 10.4 Electronics Schematics Figure - Main Electronics Board S

71 Figure 10.4-1

72

73

74

MKIII SERVICE MANUAL 3 PREFACE This document has been developed to aid an operator when a Brewer Spectrophotometer stops operating or

75

76

77

78

79

80

81

82

83

84 Figure 10.4-2

MKIII SERVICE MANUAL 4

85 Figure 10.4-3

MKIII SERVICE MANUAL 86 Figure 10.4-4

MKIII SERVICE MANUAL 87

MKIII SERVICE MANUAL 88 Figure 10.4-5

89 Figure 10.4-6

90 Figure 10.4-7

MKIII SERVICE MANUAL 91 BREWER REFERENCE DOCUMENTATION Section 10.6 Optics Figure 10.6.1 Instrument Optics Overall Dia

MKIII SERVICE MANUAL 92 Figure 10.6-1.1

93 Figure 10.6-1.2

MKIII SERVICE MANUAL 94 BA-C191/B BREWER Complete Optical Assy Item No. Part No. Description Qty 1 BA-C192 MAIN FRAME ASSY